Series IB & Series 3

Series IB Phase Converter
Permits Operation Of 220 Volt 3 Phase Motors On Single Phase Current

	CAT. NO.	PRICE	MODEL NO.	HP RANGE	CODE
	8000-100	$126.00	Model 1100B	1/4-1/2 HP	UE
	8000-101	$136.50	Model 1200B	1/2 - 1 HP	UE
	8000-102	$147.00	Model 1300B	1-3 HP	UE
	8000-103	$168.00	Model 1400B	3-5 HP	UE
	8000-104	$204.75	Model 1500B	5-7 1/2 HP	UE
	8000-105	$225.75	Model 1600B	7 1/2 - 10 HP	UE
	Your selection must be based on the horsepower of the largest motor to be started. Once running, smaller motors can be started one at a time.

Series 3 Phase Converter
Provides Continuous 3 Phase Power to 220 Volt 3 Phase Motors From 220 Volt
Single Phase Current

	CAT. NO.	PRICE	MODEL NO.	HP RANGE	CODE
	8000-012	$278.75	Model 3100	1/4 - 1/2 HP	UD
	8000-013	$341.25	Model 3200	3/4 - 1 1/2HP	UD
	8000-014	$404.25	Model 3300	2-3 HP	UD
	8000-015	$483.00	Model 3400	4-6 HP	UD
	8000-016	$630.00	Model 3500	7 1/2 - 10HP	UD
	Your selection must be based on the horsepower of the largest motor to be operated. Smaller motors may be started while the motor within the converter’s range remains running.

Application:
Cedarberg Static Phase Converters are designed to start motors within a specific horsepower range. Smaller motors may be started one at a time, once a motor within the converter’s horsepower range is running, provided that the smaller motors are wired into the same circuit.

Cedarberg Rotary Phase Converters are designed to start any motor from fractional horsepower up to the nameplate rating. If the motor on the equipment is larger than the phase converter’s nameplate rating, a phase converter of the correct size will need to be purchased. Do not attempt to start a motor that is too large for the converter or damage could occur.

Features:
Instant reversal motors present no problems to these converters. For Series 1B and Series 3 converter installations, we recommend that frequent reversing not be done for extended periods of time. Our Series 1B and Series 3 units will start more than one machine, as long as each motor is
within the horsepower range of the converter. When multiple three phase motors are on the same circuit and not within the range of the converter, the following steps must be taken:

• Start the largest motor first. (This motor must be within the converter’s range.)
  
  
• While allowing this motor to idle, additional, smaller motors may be started one at a time.
  
  
• The motor that is within the range of the Series 3 converter must remain running throughout the duty cycle of the smaller motors. With the Series 1B converter, the motor that is within the range of the converter may be turned off once the smaller motor is running and up to speed.
  
  
• Rotary Phase Converters are capable of starting any motor from fractional horsepower up to their nameplate rating. They are designed to run total horsepower loads up to three times the nameplate rating on Heavy Duty models and up to two times the nameplate rating on Standard Duty models.

Two-speed electric motors can be operated without difficulty, provided both speed ranges lie within the converter’s horsepower range. Some foreign and special motors require less starting current and therefore may require a static converter one size smaller than normal.

Rotary Phase Converters

Standard Duty Rotary Type Phase Converters
Rotary Phase Converter at an Economical Price
Produces Continuous 3 Phase Power to 220 Volt 3 Phase Motors
from 220 Volt Single Phase Current

	CAT. NO.	PRICE	MODEL NO.	NAMEPLATE RATING	CODE
	8100-051	$467.25	Model 10A	1 HP	UA
	8100-052	$582.75	Model 30A	3 HP	UA
	8100-053	$677.25	Model 50A	5 HP	UA
	8100-054	$924.00	Model 75A	7 1/2 HP	UA
	8100-055	$1076.25	Model 100A	10 HP	UA
	Your selection must be based on the largest horsepower motor to be operated. This converter is designed to operate total horsepower loads up to 2 times the nameplate rating. The largest horsepower motor you intend to start should not exceed our converter’s nameplate rating. Our converters are designed to run horsepower loads up to 3 times the nameplate rating. Designed for light starting & running loads (such as drill presses, mills, grinders, etc...) where generated 3 phase power is preferred.

Heavy Duty Rotary Type Phase Converters
Produces Balanced 3 Phase Power for Maximum Motor
Efficiency From Single Phase Current

	CAT. NO.	PRICE	MODEL NO.	MFG'S NAME PLATE RATING	UL LISTED AMPERAGE OUTPUT OF MFG. LEG (M3)	CD
	8100-001	$708.75	Model 10	1 HP	1.44	UB
	8100-002	$829.50	Model 30	3 HP	3.80	UB
	8100-003	$1044.75	Model 50	5 HP	6.00	UB
	8100-004	$1354.50	Model 75	7 1/2 HP	8.80	UB
	8100-005	$1695.75	Model 100	10 HP	11.20	UB
	8100-006	$3066.00	Model 150	15 HP	16.80	UB
	8100-007	$3617.25	Model 200	20 HP	21.60	UB
	8100-008	$4126.50	Model 250	25 HP	27.20	UB
	The largest horsepower motor you intend to start should not exceed our converter’s nameplate rating. Our converters are designed to run horsepower loads up to 3 times the nameplate rating. Designed for medium to heavy starting & running loads (such as gear head lathes, flywheel & hydraulic applications, CNC machinery, etc...) when maximum motor efficiency is required.

Reference Chart & Sizes and Weights

A	B	C	D
Series IB Permits starting of 220V 3ø motors on 220V 1ø current	Series 3 Provides continuous 3ø power to 220V 3ø motors from 220V 1ø current	Heavy Duty Rotary Produces balanced 3ø power for maximum motor efficiency from 1ø current	Standard Duty Rotary Produces continuous 3ø power to 220 3ø motors from 220V 1ø current
Features Common To All Models: • Easy Installation • Instant Reversing • Operates On 50/60 Hz • Run More Than One Machine